Schematics > Audio > 25W Mosfet audio amplifier
25W Mosfet audio amplifier25W High quality Mosfet audio amplifier circuit, no need a preamplifier.
Circuit diagram:
Parts:
| R1,R4 = 47K |
1/4W Resistors |
| R2 = 4K7 |
1/4W Resistors |
| R3 = 1K5 |
1/4W Resistors |
| R5 = 390R |
1/4W Resistors |
| R6 = 470R |
1/4W Resistors |
| R7 = 33K |
1/4W Resistors |
| R8 = 150K |
1/4W Resistors |
| R9 = 15K |
1/4W Resistors |
| R10 = 27R |
1/4W Resistors |
| R11 = 500R |
1/2W Trimmer Cermet |
| R12,R13,R16 = 10R |
1/4W Resistors |
| R14,R15 = 220R |
1/4W Resistors |
| R17 = 8R2 |
2W Resistor |
| R18 = R22 |
4W Resistor (wirewound) |
|
|
|
| C1 = 470nF |
63V Polyester Capacitor |
| C2 = 330pF |
63V Polystyrene Capacitor |
| C3,C5 = 470µF |
63V Electrolytic Capacitors |
| C4,C6,C8,C11 = 100nF |
63V Polyester Capacitors |
| C7 = 100µF |
25V Electrolytic Capacitor |
| C9 = 10pF |
63V Polystyrene Capacitor |
| C10 = 1µF |
63V Polyester Capacitor |
|
|
|
| Q1-Q5 = BC560C |
45V100mA Low noise High gain
PNP Transistors |
| Q6 = BD140 |
80V 1.5A PNP Transistor |
| Q7 = BD139 |
80V 1.5A NPN Transistor |
| Q8 = IRF532 |
100V 12A N-Channel Hexfet Transistor |
| Q9 = IRF9532 |
100V 10A P-Channel Hexfet
Transistor |
Power supply circuit diagram:
Parts:
|
R1 = 3K3 |
1/2W Resistor |
|
|
|
| C1 = 10nF |
1000V Polyester Capacitor |
| C2,C3 = 4700µF |
50V Electrolytic Capacitors |
| C4,C5 = 100nF |
63V Polyester Capacitors |
|
|
|
| D1 |
200V 8A Diode bridge |
| D2 |
5mm. Red LED |
| F1,F2 |
3.15A Fuses with sockets |
|
|
|
|
T1 |
220V Primary, 25 + 25V Secondary 120VA Mains transformer |
|
|
|
|
PL1 |
Male Mains plug |
|
|
|
|
SW1 |
SPST Mains switch |
Notes:
-
Can be directly connected to CD players, tuners and tape
recorders. Simply add a 10K Log potentiometer (dual gang for stereo) and
a switch to cope with the various sources you need.
-
Q6 & Q7 must have a small U-shaped heatsink.
-
Q8 & Q9 must be mounted on heatsink.
-
Adjust R11 to set quiescent current at 100mA (best measured
with an Avo-meter in series with Q8 Drain) with no input signal.
-
A correct grounding is very important to eliminate hum
and ground loops. Connect in the same point the ground sides of R1, R4,
R9, C3 to C8. Connect C11 at output ground. Then connect separately the
input and output grounds at power supply ground.
Technical data:
Output power: well in excess of 25Watt RMS @ 8 Ohm (1KHz sinewave)
Sensitivity: 200mV input for 25W output
Frequency response: 30Hz to 20KHz -1dB
Total harmonic distortion @ 1KHz: 0.1W0.014% 1W 0.006%10W0.006%20W0.007%25W0.01%
Total harmonic distortion @10KHz: 0.1W 0.024%1W0.016%10W0.02%20W0.045%25W0.07%
Unconditionally stable on capacitive loads
Title: 25W Mosfet audio amplifier
Source: www.electronics-lab.com
Published on: 2005-01-31
Reads: 1053
Print version:  Other schematics from Audio
Stereo Channel Selector Bass-treble tone control circuit Bass-treble tone control circuit Mini-box 2W Amplifier 10 Band Audio Equalizer 20W Power Amplifier Headphone Amplifier Improved 3 Transistor Audio Amp (80 milliwatt) Amplifier 2x30W with STK465 Portable Mixer
Schematics > Audio > 25W Mosfet audio amplifier |
Home
