Electonic circuits and schematics
Google
  Electronic circuits schematics Home Search Most popular Sitemap  
Search circuits



Categories

Circuits & schematics

  • Audio
  • Automotive
  • Games and entertainment
  • Microcontrollers
  • Miscellaneous
  • Models and model remote control
  • Motor, light and power control
  • Oscillators and timers
  • PC related
  • Power
  • RF circuit
  • Robotics
  • Security and other sensors and detectors
  • Telephone related
  • Test and measurement
  • Video and TV
  • Electronics guide

  • The very first steps
  • On the boards
  • Measuring current and voltage
  • Capacitors
  • ICs, oscillators and filters
  • Diodes I
  • Diodes II
  • Transistors
  • Analogue integrated circuits
  • Digital integrated circuits I
  • Digital integrated circuits II

  • Electronic circuits and electronic schematics


    Schematics > Audio > Ultrasonic pest repellent

    Ultrasonic pest repellent

    It is well know that pests like rats, mice etc are repelled by ultrasonic frequency in the range of 30 kHz to 50 kHz. Human beings can’t hear these high-frequency sounds. Unfortunately, all pests do not react at the same ultrasonic frequency. While some pests get repelled at 35 kHz, some others get repelled at 38 to 40 kHz. Thus to increase the effectiveness, frequency of ultrasonic oscillator has to be continuously varied between certain limits. By using this circuit design, frequency of emission of ultrasonic sound is continuously varied step-by-step automatically. Here five steps of variation are used but the same can be extended up to 10 steps, if desired. For each clock pulse output from op-amp IC1 CA3130 (which is wired here as a low-frequency square wave oscillator), the logic 1 output of IC2 CD4017 (which is a well-known decade counter) shifts from Q0 to Q4 (or Q0 to Q9). Five presets VR2 through VR6 (one each connected at Q0 to Q4 output pins) are set for different values and connected to pin 7 of IC3 (NE555) electronically. VR1 is used to change clock pulse rate. IC3 is wired as an astable multivibrator operating at a frequency of nearly 80 kHz. Its output is not symmetrical. IC4 is CD4013, a D-type flip-flop which delivers symmetrical 40kHz signals at its Q and Q outputs which are amplified in push-pull mode by transistors T1, T2, T3 and T4 to drive a low-cost, high-frequency piezo tweeter. For frequency adjustments, you may use an oscilloscope. It can be done by trial and error also if you do not have an oscilloscope. This pest repeller would prove to be much more effective than those published earlier because here ultrasonic frequency is automatically changed to cover different pests and the power output is also sufficiently high. If you want low-power output in 30-50 kHz ultrasonic frequency range then the crystal transducer may be directly connected across Q and Q outputs of IC4 (transistor amplifier is not necessary).

    Title: Ultrasonic pest repellent
    Source: www.electronic-circuits-diagrams.com
    Published on: 2005-02-01
    Reads: 1133
    Print version: Print version

    Other schematics from Audio
  • 3 Transistor Audio Amp (50 milliwatt)
  • 3 Line Mixer
  • 3 Channel Spectrum Analyzer
  • FET Audio Mixer
  • 100W Audio Amplifier
  • Two way cross-over 3500 Hz
  • Stereo Preamplifier with Bass-boost
  • 100W Guitar Amplifier
  • Improved 3 Transistor Audio Amp (80 milliwatt)
  • Amplified Ear

  • Schematics > Audio > Ultrasonic pest repellent


    fish - ñóáòèòðè - ðóëåòêà - êîìïîíåíòû - ïëàíåòû - Åâðîïà - Ãàëåðåÿ
    Page generation 0.012 seconds
    Ultrasonic pest repellent